260W 3in1 Stage Beam &Gobo Move Head Light

Product Instruction

lamp: OSRAM 10R or YODN 10R  (life:2200 hours Color temperature: 8000K)Channel mode:20 DMX512 ChannelPan scan:540°(16bit) Electric correctionTilt scan:270° (16bit) Electric correctionAmazing dot matix, four tact switch, 180° turning showColor wheel: one color wheel, 14 kinds of color chips in one color wheelGobo: 17 gobos + 8 glass gobosEffect Wheel:  Rotation eight prism, effect move , frost0-100% mechanical dimming, mechanical dimming and free dimming available.strobe macro control available.   Lens optical system achanical fouce .beam angle 0~4°Over heat protectionPower Input: 100-240V,50/60HzPower Dissipation:350W IP level :IP20Magnetic ballast and AC/Dc power supplyProduct Size:523×337×511mmPacking Size: 635X440X725Net weight:19.5KG

1.5  Cable connection(DMX)Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use microphone cable or other cable with characteristics differing from those specified. The end connections must be made using XLR type 3 or 5-pin male/female connectors. A terminating plug must be inserted into the last projector with a resistance of 120Ohm (minimum 1/4 W) between terminals 2 and 3.
IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be connected to the shield braid and to pin 1 of the connectors.
Figure 1  DMX Cable connection1.6  Rigging (Optional)This equipment can be positioned and fixed by clamp in every direction of the stage. Locking system makes it easy to fasten to the bracket.
Attention! Two clamps is needed to fix the equipment. Every clamp is locked by fastener of 1/4 kind. Fastener can only be locked clockwise.
Attention! Fasten a safety string to the additional hole of side aluminum piece. The secondary accessory can not hang on the delivery handle. Nip the equipment on bracket.

Check if rigging clamp (not including the one inside) damaged or not? If stand ten times weight as the equipment. Make sure the architecture can stand ten times weight as all the equipments, clamps, wirings and other additional fixtures.Screws for clamping must be fixed firmly. Take one M12 screw (Grade 8.8 or higher) to clamp bracket, and then screw the nuts.Level the two hanging points at the bottom of clamp. Insert fastener to the bottom, lock the two levers by 1/4 rotating clockwise; then install another clamp.Install on safety string which stands at least ten times weight as equipment. Terminal of the accessory is designed for clamps.Make sure pan/tilt lock unlocked or not. Keep the distance more than 1M from equipment to flammable material or lighting source.

Figure 2  Installation Chapter 2  Panel operation2.1  BriefThe light panel diagram show as Figure 3, Left area is TFT Displayer, support touch, and right area is KEY, both of touch and KEY can operate light and setting.
Display & operation just like 'Android operation system', touch the item will set or modify setting. 
Note: Prevent damage the touch or TFT displayer, Can not use sharp objects chick displayer. 

Figure 3  Panel diagram2.2  Operation2.2.1 Operate light with touch or KEY

The left area is TFT Displayer and touch, chick item or value with finger will to complete operation of set light setting(parameters) or view light state.The area on the right hand side is 4 KEY, As auxiliary input interface, if  disable touch function,, the KEYr can been choose to set the parameter.

2.2.2 Parameter value settingWhen the selected item is value need to been modified, the dialog shown in Figure 4 will popup.

Figure 4  Dialog of value setting

Modify value:Can quickly modify value via pull the slider to the desired position, or click  the button of 'up' or 'down' whit finger on the right side to set the exact desired value, another way is roll encoder on the right hand side of panel.Apply value:When Value had been modified, Then press the bottom of 'apply' in the left corner to apply to the light, but hav't saved;Save Value:Any time, click on the lower right corner of the "OK" button, the setting will been saved into internal memory.

2.2.3 Boolean parameter setting

when the selected parameters is a Boolean value (such as ON or OFF), can directly modify setting by chick corresponding item, the setting will been saved right now. When the parameter is a key item, chick corresponding item, a dialog shown in Figure 5 will been popup ask for the confirm. Chick 'sure' to confirm.

Figure 5  Dialog of confirm2.2.4 Sub Menu(Parameter)Chick item of main menu, enter corresponding sub menu, shown in Figure 6, total 6 sub menu, includes class of parameter and status:

ADDRESS:Set light DMX address.WORKMOD:Set light work mode, master or slave mode when in auto run mode.DISPLAY: Set display parameter, eg. select language.TEST:Used for test light, modify DMX channel data to test function, the corresponding function  of reference channel function table.ADVANCE:Set light running parameter.STATUS:view light current status.

Figure 6  Parameter menu


 2.3  Operation and parameter instructionVia following operation, enter sub menu(parameter menu) shown in Figure 6

In main menu, chick 1/6 function button into corresponding parameter menu.In sub menu(page), chick main item on the left side of displayer, can shift to corresponding sub menu(page) quickly.

2.3.1 ADDR--> Address: Set DMX AddressClick and select the "ADDR", can enter the page of DMX address setting, range from 1 to 512, the address code shouldn't is not greater than (512- channels quantity), otherwise the light will not been controlled. Following is the operation:
Enter the page of DMX address, as shown in Figure 7, click the blank area in right side of display will pop-up diglog as in Fig. 4, modify value, then click 'ENTER' to confirm and save DMX address code.

Figure 7  page of DMX Address2.3.2 MODE--> WorkMode: Set Light work modeEnter the page of 'WorkMode' as shown in Figure 8 and modify setting. Can set light work mode, control lamp and DMX channel mode.

Figure 8  page of work mode
    DMX Ctrl:     Choose to set  DMX Mode,
    Auto Run:     Choose to set  Auto Mode,
    Sound Ctrl:    Choose to set  Sound Mode,
    M/S Choose:Available just in 'AUTO RUN' or 'SOUND Ctrl' mode.
      ON--> Master. (Data will be send to other slave lamp immediately.)
     OFF--> Slaver.(NOT send data to other lamp via DMX Cable).(Default)  
    Light Switch:  
      ON--> Turn on the light,
     OFF--> Turn off the light.
    Channel Qty: Light support 2 DMX Channel mode: sample or extend.
     Simple --> 16CH.(Default)  
     Expand--> 20CH(or null).2.3.3 DISP-->DISPLAY: Set displayLight support 2 language, rotation display,Enter page as shown in Figure9 to set parameter following:

Figure9   page of display
    Language:  English /Chinese
    Screen Saver: when panel is idle(these is no operation in 10 second), displayer will enter saver status.
      OFF--> No screen saver.
  Mode1--> Power-saving mode, turn off the display.
  Mode2--> Displays the current address.
  Mode3--> Displays the icon and the current working mode.(Default)
    Screen Rotion: To turning display.
      ON--> Normal display.(Default)
  OFF--> 180° turning display.
    Touch enable:Disable or enable touch function,.
      ON--> Enable touch function.(Default)
  OFF--> Dosable touch function.
    Touch adjust:Adjust touch function. Normally, not enter this item.







 2.3.4 TEST--> TestModeEnter the page as shown in Figure 10, Light will into test mode, in this mode, the light does not receive the data for DMX controller.:

Figure 10  page of Test
    PAN:      range for 0 to 255;
    TILT:      range for 0 to 255;
    FOCUS:    range for 0 to 255;
    COLOR:    range for 0 to 255;
    GOBO:     range for 0 to 255;
    PRISM:     range for 0 to 255;
    FROST:     range for 0 to 255;;
    STROBE:   range for 0 to 255;2.3.5 ADVA-->Advanced: Set light run parameterEnter the page as shown in Figure 10, set the parameter of light:

Figure 11  page of run parameter
    Pan Invert:  Reverse PAN move
      OFF--> Pan Normal move.(Default)
       ON--> Reverse PAN move.
    Tilt Invert:  Reverse TILT move
      OFF--> Tilt Normal move.(Default)
       ON--> Reverse Tilt move.
    P/T Rectify: Disable or enable position rectify function.
      OFF--> Disable P/T rectify
       ON--> Enable P/T rectify-(Default)
    Pan Offset:     Set PAN original position. Default: 10
    Tilt Offset:      Set TILT original position. Default: 10
    Lamp when:    
      PowerON--> Turn on the lamp when power on.(Default)
      RstDone--> Turn on the lamp after reset.
      Manual--> Manually turn on the lamp.
    Data hold:     
      OFF--> When no DMX signal,return to middle position.(Default)
       ON--> When no DMX signal,stop in the final position.
    Factory Setting:  Restore all parameter to factory setting.2.3.6 STAT-->Status: View status Enter the page as shown in Figure 12:

Figure 12  page of status
     Work Mode:  Show the current working mode.
     Address:     Show the current address.
     Version:      Show the version of the lamp.
     Elapse:      Working hours after turn on.
     Tatol:        Cumulative hours of operation

 Chapter 3  Channel description3.1  Channel tableLight DMX mode:  20ch (extend), as shown in Table 1:
Table 1  Channel brief